Salicru SLC-1000 TWIN PRO Instrukcja Użytkownika

UNINTERRUPTIBLE POWER SUPPLY (UPS) + LIGHTING FLOW DIMMER STABILIZERS (ILUEST) + SWITCH MODE POWER SUPPLY + STATIC INVERTERS + PHOTOVOLTAIC INVERTERS

10Protection cover for smart slotOutput socketsInput socket Input breaker protection FanUSBTransient protection (*)EPOExtended autonomy connectorProte

11SALICRU Model from 3 kVA (standard) Model from 3 kVA (B1)(*) Transient protection (fax, modem,...)Output socketsInput socket Input breaker protec

12Battery module for models 0.7 and 1 kVA Battery module for models 1.5 from 3 kVAFig. 5. Front view from battery module.Battery module for models 0

13SALICRU3.2. Definition of the product.3. 2.1. Nomenclature.SLC-2000-TWIN PRO (B1) WCO “EE29503”MOD BAT TWIN PRO 2x6AB003 40A WCO “EE29503”EE* Spe

143.3. Operating principle.This manual describes the installation and operating of the Un-interruptible Power Supply (UPS) from SLC TWIN PRO series a

15SALICRUThe available SNMP option for SLC TWIN PRO series is a card to be inserted into the slot that the UPS has in its rear side.The connection of

164. Installation.• Check the Safety instructions, from section 1.2.3.• Check that the data in the nameplate are the required by the installation.•

17SALICRU  Battery module: – The own module. – 1 trunk with Anderson connectors at its ends in order to do the connection between the battery module

184.3.2. Connection to output.• As this is a device with class I protection against electric shocks, it is essential to install a protective earth c

19SALICRU4.3.4. Connection of main input earth terminal ( ) and the earth bonding terminal ( ).• As this is a device with class I protection against

20SW2 "On"SW3 "Off"SW1 (*)Relays interface cardInternal relays147 1 (GND) 13 12 11 10 9 6 5 4 3 28Fig. 8. Relays interface p

21SALICRU5. Operating.5.1. UPS commissioning and shutdown.5.1.1. Preliminary controls.• Make sure that all connections have been done properly, an

226. Control panel with LCD.6.1. Control panel.Fig. 10. Control panel view.Key Function DescriptionSELECT keyUPS on bypass mode, the output voltage

23SALICRUBypass operating informationInverter operating informationOutput informat.Load informat.Battery informationInformat. of the Mode/Fault/Warnin

246.2.3. Line mode.The LCD panel on line mode is shown in figure 14. The infor-mation about mains, battery, UPS output and load will be dis-played. T

25SALICRU6.3. Settings through the LCD panel of the synoptic.Output voltage and frequency, bypass status, ECO mode and Con-verter mode can be set thr

267. Maintenance, warranty and service.7.1. Battery maintenance.• Pay attention to the safety instructions regarding battery and the stated in sect

27SALICRU7.2 .1. Troubleshooting guide. Warning indications.If the UPS doesn’t work properly, before calling S.S.T. try to resolve the problem using

287.3. Warranty conditions.The limited warranty only applies to those products that you ac-quire for commercial or industrial use in the normal devel

29SALICRU8. Annexes.8.1. General technical specifications.Available powers (kVA / kW) 0.7 / 0.56 1 / 0.8 1.5/ 1.2 2 / 1.6 3 / 2.4Technology On-line

3SALICRUGeneral index1. Introduction.1.1. Acknowledgement letter.1.2. Using this manual.1.2.1. Conventions and used symbols.1.2.2. For more infor

30Available powers (kVA / kW) 0.7 / 0.56 1 / 0.8 1.5/ 1.2 2 / 1.6 3 / 2.4End battery voltage:- From 0-30 % load, block / set 10.7 V DC / 32.1 V DC 10.

31SALICRUpower but in alternating current can defer depending on the power factor.• LCD.- LCD acronym of Liquid Crystal Display, device in-vented by

UNINTERRUPTIBLE POWER SUPPLY (UPS) + LIGHTING FLOW DIMMER STABILIZERS (ILUEST) + SWITCH MODE POWER SUPPLY + STATIC INVERTERS + PHOTOVOLTAIC INVERTERS

4 SALICRU1. Introduction.1.1. Acknowledgement letter.We would like to thank you in advance for the trust you have placed in us by purchasing this pr

5SALICRUcould be a risk on your safety or on the other/s persons, being able to make serious injuries even the death, also it can cause damages to the

6open, so the button must be switched to close the circuit and the voltage to the loads is broken. To establish the power supply to the loads again, t

7SALICRU1.2.3.3. Safety warning regarding batteries.• The manipulation and connection of the batteries shall be done and supervised by personnel wit

82. Quality and standard guarantee.2.1. Declaration of the management.Our target is the client’s satisfaction, therefore this Management has decided

9SALICRU3. Presentation.3.1. Views.3.1.1. Views of the equipment.Figures 1 to 3 show the illustrations of the equipment according to the case forma